// A simple OSD implementation. Can be hooked up between a cores
// VGA output and the physical VGA pins

module osd (
	// OSDs pixel clock, should be synchronous to cores pixel clock to
	// avoid jitter.
	input        clk_sys,

	// SPI interface
	input        SPI_SCK,
	input        SPI_SS3,
	input        SPI_DI,

	input  [1:0] rotate, //[0] - rotate [1] - left or right

	// VGA signals coming from core
	input  [5:0] R_in,
	input  [5:0] G_in,
	input  [5:0] B_in,
	input        HSync,
	input        VSync,

	// VGA signals going to video connector
	output [5:0] R_out,
	output [5:0] G_out,
	output [5:0] B_out
);

parameter OSD_X_OFFSET = 10'd0;
parameter OSD_Y_OFFSET = 10'd0;
parameter OSD_COLOR    = 3'd0;

localparam OSD_WIDTH   = 10'd256;
localparam OSD_HEIGHT  = 10'd128;

// *********************************************************************************
// spi client
// *********************************************************************************

// this core supports only the display related OSD commands
// of the minimig
reg        osd_enable;
(* ramstyle = "no_rw_check" *) reg  [7:0] osd_buffer[2047:0];  // the OSD buffer itself

// the OSD has its own SPI interface to the io controller
always@(posedge SPI_SCK, posedge SPI_SS3) begin
	reg  [4:0] cnt;
	reg [10:0] bcnt;
	reg  [7:0] sbuf;
	reg  [7:0] cmd;

	if(SPI_SS3) begin
		cnt  <= 0;
		bcnt <= 0;
	end else begin
		sbuf <= {sbuf[6:0], SPI_DI};

		// 0:7 is command, rest payload
		if(cnt < 15) cnt <= cnt + 1'd1;
			else cnt <= 8;

		if(cnt == 7) begin
			cmd <= {sbuf[6:0], SPI_DI};

			// lower three command bits are line address
			bcnt <= {sbuf[1:0], SPI_DI, 8'h00};

			// command 0x40: OSDCMDENABLE, OSDCMDDISABLE
			if(sbuf[6:3] == 4'b0100) osd_enable <= SPI_DI;
		end

		// command 0x20: OSDCMDWRITE
		if((cmd[7:3] == 5'b00100) && (cnt == 15)) begin
			osd_buffer[bcnt] <= {sbuf[6:0], SPI_DI};
			bcnt <= bcnt + 1'd1;
		end
	end
end

// *********************************************************************************
// video timing and sync polarity anaylsis
// *********************************************************************************

// horizontal counter
reg  [9:0] h_cnt;
reg  [9:0] hs_low, hs_high;
wire       hs_pol = hs_high < hs_low;
wire [9:0] dsp_width = hs_pol ? hs_low : hs_high;

// vertical counter
reg  [9:0] v_cnt;
reg  [9:0] vs_low, vs_high;
wire       vs_pol = vs_high < vs_low;
wire [9:0] dsp_height = vs_pol ? vs_low : vs_high;

wire doublescan = (dsp_height>350);

reg ce_pix;
always @(posedge clk_sys) begin
	integer cnt = 0;
	integer pixsz, pixcnt;
	reg hs;

	cnt <= cnt + 1;
	hs <= HSync;

	pixcnt <= pixcnt + 1;
	if(pixcnt == pixsz) pixcnt <= 0;
	ce_pix <= !pixcnt;

	if(hs && ~HSync) begin
		cnt    <= 0;
		if (cnt <= 512) pixsz = 0;
		else pixsz  <= (cnt >> 9) - 1;
		pixcnt <= 0;
		ce_pix <= 1;
	end
end

always @(posedge clk_sys) begin
	reg hsD, hsD2;
	reg vsD, vsD2;

	if(ce_pix) begin
		// bring hsync into local clock domain
		hsD <= HSync;
		hsD2 <= hsD;

		// falling edge of HSync
		if(!hsD && hsD2) begin
			h_cnt <= 0;
			hs_high <= h_cnt;
		end

		// rising edge of HSync
		else if(hsD && !hsD2) begin
			h_cnt <= 0;
			hs_low <= h_cnt;
			v_cnt <= v_cnt + 1'd1;
		end else begin
			h_cnt <= h_cnt + 1'd1;
		end

		vsD <= VSync;
		vsD2 <= vsD;

		// falling edge of VSync
		if(!vsD && vsD2) begin
			v_cnt <= 0;
			vs_high <= v_cnt;
		end

		// rising edge of VSync
		else if(vsD && !vsD2) begin
			v_cnt <= 0;
			vs_low <= v_cnt;
		end
	end
end

// area in which OSD is being displayed
wire [9:0] h_osd_start = ((dsp_width - OSD_WIDTH)>> 1) + OSD_X_OFFSET;
wire [9:0] h_osd_end   = h_osd_start + OSD_WIDTH;
wire [9:0] v_osd_start = ((dsp_height- (OSD_HEIGHT<<doublescan))>> 1) + OSD_Y_OFFSET;
wire [9:0] v_osd_end   = v_osd_start + (OSD_HEIGHT<<doublescan);
wire [9:0] osd_hcnt    = h_cnt - h_osd_start;
wire [9:0] osd_vcnt    = v_cnt - v_osd_start;
wire [9:0] osd_hcnt_next  = osd_hcnt + 2'd1;  // one pixel offset for osd pixel
wire [9:0] osd_hcnt_next2 = osd_hcnt + 2'd2;  // two pixel offset for osd byte address register
reg        osd_de;

reg [10:0] osd_buffer_addr;
wire [7:0] osd_byte = osd_buffer[osd_buffer_addr];
reg        osd_pixel;

always @(posedge clk_sys) begin
	if(ce_pix) begin
		osd_buffer_addr <= rotate[0] ? {rotate[1] ? osd_hcnt_next2[7:5] : ~osd_hcnt_next2[7:5],
		                                rotate[1] ? (doublescan ? ~osd_vcnt[7:0] : ~{osd_vcnt[6:0], 1'b0}) :
		                                            (doublescan ?  osd_vcnt[7:0]  : {osd_vcnt[6:0], 1'b0})} :
		                               {doublescan ? osd_vcnt[7:5] : osd_vcnt[6:4], osd_hcnt_next2[7:0]};

		osd_pixel <= rotate[0]  ? osd_byte[rotate[1] ? osd_hcnt_next[4:2] : ~osd_hcnt_next[4:2]] :
		                          osd_byte[doublescan ? osd_vcnt[4:2] : osd_vcnt[3:1]];

		osd_de <= osd_enable &&
		    (HSync != hs_pol) && ((h_cnt + 1'd1) >= h_osd_start) && ((h_cnt + 1'd1) < h_osd_end) &&
		    (VSync != vs_pol) && (v_cnt >= v_osd_start) && (v_cnt < v_osd_end);
	end
end

assign R_out = !osd_de ? R_in : {osd_pixel, osd_pixel, OSD_COLOR[2], R_in[5:3]};
assign G_out = !osd_de ? G_in : {osd_pixel, osd_pixel, OSD_COLOR[1], G_in[5:3]};
assign B_out = !osd_de ? B_in : {osd_pixel, osd_pixel, OSD_COLOR[0], B_in[5:3]};

endmodule