Activity

From 10/09/2019 to 11/07/2019

10:53 PM Bug #83: Many USB hubs do not work: This setup is so much better for debugging than on the Eclaire. I have gdb on linux to debug the binary, I can printf... foft
10:49 PM Bug #83: Many USB hubs do not work: The hub is detected as connected, then it tries to set the address and fails.
So, the keyboards I'm using are low ... foft
10:07 PM Bug #83: Many USB hubs do not work: OK, circuit build and wired up. I can type on the sockit.
Now to get some debugging in place and try the hub. foft

08:57 PM Bug #83: Many USB hubs do not work: Wired up the USB to gpio, added another pll for the pll clock.
Now will get the software to poll usb and see if I ... foft

10:12 PM Bug #83: Many USB hubs do not work: Updating the avalon arm regs, to the latest zpu config regs. Which has USB...
Will also add another avalon slave ... foft

10:38 PM Bug #83: Many USB hubs do not work: Managed to get the core flashing ok (was bad rbf generation).
Also installed gcc and the binaries are running ok.
C... foft

10:21 PM Bug #83: Many USB hubs do not work: Well I can flash it and get sync on vga, but no dice. I remembered I needed to run the firmware binary. I flashed the... foft
08:24 PM Bug #83: Many USB hubs do not work: Managed to get the SOCkit board up and running and set up linux.
Now going to build/flash the existing 800 core as ... foft
09:25 AM Bug #83: Many USB hubs do not work: I've known about this for a long time but have never really looked into it, since its a pain and hubs are not that im... foft
09:23 AM Bug #83 (Closed): Many USB hubs do not work: Only the hub I did initial testing with works. Investigate why. foft

10:34 PM Feature #82 (New): Setting for mono pokey: Hias asked me for a mono pokey mode, where its output to both speakers.
foft
10:17 PM Bug #75 (Closed): USB keyboard stops functioning after idle period: foft
10:17 PM Bug #75 (Resolved): USB keyboard stops functioning after idle period: Added a timer elapsed function that handles the overflow. This makes the max delay 35 mins, but I think that is ok...... foft
09:32 PM Bug #75: USB keyboard stops functioning after idle period: ((2^32)/1e6)/60 = 71...
So trivial fix. I clearly don't need the Saleae to debug this one, but that isn't so bad. ... foft
09:30 PM Bug #75: USB keyboard stops functioning after idle period: Trying it with two keyboards. So far an hour and working.
Though I have a hunch that it'll stop working in 10 minu... foft
10:15 PM Revision 956 (repo2): Bug#75: Fix USB keyboard hang after 70 minutes: markw

10:47 PM Bug #75 (In Progress): USB keyboard stops functioning after idle period: foft
10:36 PM Bug #75: USB keyboard stops functioning after idle period: OK, finally froze. I could still enter the menu with fire and it worked. So ZPU is alive, just USB is dead.
Ordere... foft
10:22 PM Bug #75: USB keyboard stops functioning after idle period: I left it for an hour, then typed and it worked... sigh. foft
09:25 PM Bug #75: USB keyboard stops functioning after idle period: While I mull that I tried building a core that can enter the menu with fire. So I can see if it is indeed USB that cr... foft
09:24 PM Bug #75: USB keyboard stops functioning after idle period: Tempted to get a Saleae logic USB3 analyzer to capture at a higher rate and they also have USB decoding. Its several ... foft
09:23 PM Bug #75: USB keyboard stops functioning after idle period: So, decided to take it seriously.
My picoscope claimes to decode USB, tried that and found it pretty poor.
So I tri... foft
09:21 PM Bug #75: USB keyboard stops functioning after idle period: Jurgen has this with both his keyboards after about 20 minutes.
I also thought I saw it when running the Eclaire for... foft

Also available in: Atom

EclaireXL