Pinouts » History » Version 12
foft, 04/15/2018 08:09 PM
| 1 | 1 | foft | h1. Pinouts |
|---|---|---|---|
| 2 | 3 | foft | |
| 3 | 2 | foft | h2. V1 |
| 4 | 3 | foft | |
| 5 | 9 | foft | h3. Use in core |
| 6 | |||
| 7 | *Cartridge/PBI interface* |
||
| 8 | 10 | foft | 1: CCTL_N |
| 9 | 2: PHI2 |
||
| 10 | 3: RD5 |
||
| 11 | 4: RW_N |
||
| 12 | 5: A10 |
||
| 13 | 6: A11 |
||
| 14 | 7: S5_N |
||
| 15 | 8: D7 |
||
| 16 | 9: D6 |
||
| 17 | 10:D3 |
||
| 18 | 11:NC |
||
| 19 | 12:NC |
||
| 20 | 13:D0 |
||
| 21 | 14:A12 |
||
| 22 | 15:D1 |
||
| 23 | 16:A9 |
||
| 24 | 17:D2 |
||
| 25 | 18:A8 |
||
| 26 | 19:D5 |
||
| 27 | 20:A7 |
||
| 28 | 21:D4 |
||
| 29 | 22:A6 |
||
| 30 | 23:A0 |
||
| 31 | 24:A5 |
||
| 32 | 25:A1 |
||
| 33 | 26:A4 |
||
| 34 | 27:A2 |
||
| 35 | 28:A3 |
||
| 36 | 29:MIC_PBI (To ADC jumper) |
||
| 37 | 30:MIC_PBI (To ADC jumper) |
||
| 38 | 31:RD4 |
||
| 39 | 32:S4_N |
||
| 40 | 33:EXTSEL_N |
||
| 41 | 34:A13 |
||
| 42 | 35:A14 |
||
| 43 | 36:A15 |
||
| 44 | 37:MPD_N |
||
| 45 | 38:REF_N |
||
| 46 | 39:IRQ_N |
||
| 47 | 40:RST_N |
||
| 48 | 9 | foft | |
| 49 | 10 | foft | *SIO interface* |
| 50 | 1: SIO CLOCK OUT |
||
| 51 | 2: SIO COMMAND |
||
| 52 | 3: SIO IN |
||
| 53 | 4: SIO PROCEED |
||
| 54 | 5: SIO IRQ |
||
| 55 | 6: SIO CLOCK IN |
||
| 56 | 7: SIO OUT |
||
| 57 | 8: SIO MOTOR EN |
||
| 58 | 9: SIO MIC (To ADC jumper) |
||
| 59 | 10:SIO MOTOR EN |
||
| 60 | 9 | foft | |
| 61 | h3. By connection to FPGA |
||
| 62 | 1 | foft | |
| 63 | 10 | foft | Useful information if building your own core. |
| 64 | In general pins have 100 ohm resistance to the FPGA itself. The FPGA max voltage on IO is 3.3V. |
||
| 65 | |||
| 66 | 11 | foft | *GPIO A:* |
| 67 | 10 | foft | 1-10: Direct to FPGA |
| 68 | 11: 5V |
||
| 69 | 12: GND |
||
| 70 | 13-28: Direct to FPGA |
||
| 71 | 29: 3.3V |
||
| 72 | 30: GND |
||
| 73 | 1 | foft | 31-40: Direct to FPGA |
| 74 | 11 | foft | |
| 75 | *GPIO B:* |
||
| 76 | 1-10: Direct to FPGA |
||
| 77 | 11: GND |
||
| 78 | 12: GND |
||
| 79 | 13: 3.3V |
||
| 80 | 14: 5V |
||
| 81 | 10 | foft | |
| 82 | *Cartridge/PBI interface* |
||
| 83 | All level shifted to 3.3V. |
||
| 84 | Special pins: |
||
| 85 | 31:10k pulldown |
||
| 86 | 3: 10k pulldown |
||
| 87 | 10/11: NC |
||
| 88 | 29:To ADC jumper (PBI) |
||
| 89 | 30:To ADC jumper (PBI) |
||
| 90 | 33:4.7k pullup to 5V |
||
| 91 | 37:4.7k pullup to 5V |
||
| 92 | 38:4.7k pullup to 5V |
||
| 93 | 39:4.7k pullup to 5V |
||
| 94 | |||
| 95 | *SIO interface* |
||
| 96 | 1-7: 3.3V level shifted, 5V pull-up. |
||
| 97 | 8,10: 5V transistor drive (for tape motor) |
||
| 98 | 9: To ADC jumper (SIO) |
||
| 99 | |||
| 100 | 2 | foft | h2. V2 |
| 101 | 6 | foft | |
| 102 | h3. Use in core |
||
| 103 | |||
| 104 | *Interface 1:* |
||
| 105 | 1-16: A0-A15 (1=A0,2=A1, etc) |
||
| 106 | 17-24: D0-D7 (17=D0, 18=D1 etc) |
||
| 107 | 25: PHI2 |
||
| 108 | 26: HALT (not implemented yet) |
||
| 109 | 27: RST_N |
||
| 110 | 28: IRQ_N |
||
| 111 | 29: D1XX (not implemented yet) |
||
| 112 | 30: CASINH_N |
||
| 113 | 31: CCTL_N |
||
| 114 | 32: REF_N |
||
| 115 | 33: CAS_N |
||
| 116 | 7 | foft | 34: MPD_N |
| 117 | 35: RAS_N |
||
| 118 | 36: RW_N |
||
| 119 | 37: RD4 |
||
| 120 | 38: S4_N |
||
| 121 | 39: S5_N |
||
| 122 | 40: RD5 |
||
| 123 | |||
| 124 | *Interface 2:* |
||
| 125 | 1: USBDM (FTDI USB RS232) |
||
| 126 | 2: USBRES (FTDI USB RS232) |
||
| 127 | 3: USBDP (FTDI USB RS232) |
||
| 128 | 4: GND |
||
| 129 | 5: 5V0 |
||
| 130 | 6: 5V0 |
||
| 131 | 7: J2 ANAL_B (Paddle in) |
||
| 132 | 8: J2 ANAL_A |
||
| 133 | 9: J1 ANAL_B |
||
| 134 | 10:J1 ANAL_A |
||
| 135 | 11:J2 FIRE |
||
| 136 | 12:J2 UP |
||
| 137 | 13:J2 DOWN |
||
| 138 | 14:J2 LEFT |
||
| 139 | 15:J2 RIGHT |
||
| 140 | 16:J1 FIRE |
||
| 141 | 17:J1 UP |
||
| 142 | 18:J1 DOWN |
||
| 143 | 19:J1 LEFT |
||
| 144 | 20:J1 RIGHT |
||
| 145 | 21:J4 FIRE |
||
| 146 | 22:J4 UP |
||
| 147 | 23:J4 DOWN |
||
| 148 | 24:J4 LEFT |
||
| 149 | 25:J4 RIGHT |
||
| 150 | 26:J3 FIRE |
||
| 151 | 27:J3 UP |
||
| 152 | 28:J3 DOWN |
||
| 153 | 29:J3 LEFT |
||
| 154 | 30:J3 RIGHT |
||
| 155 | 31:GND |
||
| 156 | 6 | foft | 32:SIO IRQ |
| 157 | 1 | foft | 33:SIO PROCEED |
| 158 | 8 | foft | 34:SIO MOTOR_EN |
| 159 | 35:SIO COMMAND |
||
| 160 | 36:SIO DATA OUT |
||
| 161 | 1 | foft | 37:SIO DATA IN |
| 162 | 38:CLOCK OUT |
||
| 163 | 39:CLOCK IN |
||
| 164 | 6 | foft | 40:EXTSEL_N |
| 165 | |||
| 166 | 1 | foft | h3. By connection to FPGA |
| 167 | |||
| 168 | Useful information if building your own core. |
||
| 169 | 5 | foft | In general pins have 100 ohm resistance to the FPGA itself. The FPGA max voltage on IO is 3.3V. |
| 170 | 1 | foft | |
| 171 | *GPIO:* |
||
| 172 | 1-17: direct to FPGA |
||
| 173 | 18: SDA (i2c) - clock gen also on here (*V2 FIX only*) |
||
| 174 | 19: SCL (i2c) - clock gen also on here (*V2 FIX only*) |
||
| 175 | 20-22: GND |
||
| 176 | 12 | foft | 23-24: 3.3V |
| 177 | 1 | foft | 25-26: 5.0V |
| 178 | |||
| 179 | *Interface 1:* |
||
| 180 | All level shifted to 3.3V. |
||
| 181 | Special pins: |
||
| 182 | 10 | foft | 37:10k pulldown |
| 183 | 40:10k pulldown |
||
| 184 | 34:4.7k pullup to 5V |
||
| 185 | 28:4.7k pullup to 5V |
||
| 186 | 32:2k pullup to 5V (*V2 FIX 2k, V2 4.7k*) |
||
| 187 | 1 | foft | |
| 188 | *Interface 2:* |
||
| 189 | 1-3: USB to FTDI |
||
| 190 | 4: GND |
||
| 191 | 5,6: 5V |
||
| 192 | 10 | foft | 7-10: Charge cap, FPGA compares with ref voltage (about 2V) |
| 193 | 11-30: level shifted to 3.3V. 4.7k pullup to 5V. Direction pins have extra 220 ohm resistance in addition (330 ohm total to FPGA). |
||
| 194 | 1 | foft | 31: GND |
| 195 | 32-33: level shifted to 3.3V. 4.7k pullup to 5V |
||
| 196 | 34: 5V transistor drive (for tape motor) |
||
| 197 | 10 | foft | 35-40: level shifted to 3.3V. 4.7k pullup to 5V |