Activity

From 06/01/2017 to 06/30/2017

06/30/2017

11:30 PM Bug #52: Atari Control Picture: foft wrote:
> I checked an older core in case I introduced it with the antic timing changes for pbi. Was bad then, s... Stephen
10:15 PM Bug #52: Atari Control Picture: I checked an older core in case I introduced it with the antic timing changes for pbi. Was bad then, so unrelated.
... foft
10:10 PM Feature #14: Svideo core for first prototype: Added a poke 712,15 for comparison of max values. Interesting how the amplitude for basic 'blue' is so much higher ye... foft
09:54 PM Feature #14: Svideo core for first prototype: I mean see how the 'white' on ready already takes most of the range, without trying to increase it. foft
09:54 PM Feature #14: Svideo core for first prototype: Atari
!composite_atari_basic.png!
Eclaire
!composite_eclaire_basic.png!
We have a range of 0-1v on the DAC. 0... foft
09:50 PM Feature #14: Svideo core for first prototype: Added traces of Atari basic from the scope, to see the voltage level differences.
Eclaire is driving my monitor, A... foft

06/29/2017

11:30 PM Bug #52 (Closed): Atari Control Picture: CORE14, PAL & NTSC exhibit the same behaviour. When displaying the attached Atari Control Picture, the colour blocks... Stephen
08:59 PM Bug #49: CORE13 - NTSC/PAL switching: I think I've identified the problem. If the zpu happens to exit the menu at the end of an 'original' cycle the pbi lo... foft

06/27/2017

07:54 PM No news: No news, I've been ill but am almost better!
Is anyone still alive here?
On an unrelated note found this artic... foft

06/23/2017

07:27 AM Feature #11: Non-uk keyboard support (custom keyboard mapping): It's written in c. The Atari core is built with a DMA port and the ability to freeze the 6502. Outside that there is ... foft
04:31 AM Feature #11: Non-uk keyboard support (custom keyboard mapping): Okay, sounds great. So, is the system menu actually an Atari program or is it VHDL code?
917k

06/22/2017

09:12 PM Feature #11: Non-uk keyboard support (custom keyboard mapping): Yeah, that should work. You just described a multiplexor btw.
Got guests this weekend, so will do the plumbing nex... foft

06/21/2017

11:30 PM Feature #11: Non-uk keyboard support (custom keyboard mapping): Mark,
It works great! Very Cool! Thank you for the test build. If we can add a toggle to the system menu and assig... 917k
08:56 PM Feature #11: Non-uk keyboard support (custom keyboard mapping): I put up a build with your mapping as ansikbd.sof in the usual place. Let me know if it works as expected please. foft
09:44 AM Feature #11: Non-uk keyboard support (custom keyboard mapping): Thanks
11 is left alt
extended 11 is right alt - I use 1xx for extended xx.
I'll build a test core with your c... foft
02:55 AM Feature #11: Non-uk keyboard support (custom keyboard mapping): Rethinking this, I'm not sure if we need to have a user-mappable keyboard at all as long as we have support for both ... 917k
02:37 AM Feature #11: Non-uk keyboard support (custom keyboard mapping): TEST 917k
12:06 AM Feature #11: Non-uk keyboard support (custom keyboard mapping): I would say just use a text file, it's easier to create/edit. Also, The EclaireXL could have keys that have no equiva... 917k
09:02 PM Bug #33: Wizard of Wor: I'm going to build a debug tool to make it easier to track these things down.
For now, a workaround. Use 2x turbo ... foft

06/20/2017

09:41 PM Feature #2: PBI support: Excellent! sadosp
07:08 PM Feature #2: PBI support: Hias tried out PBI on the v1.
Surprise: Turbo freezer didn't work! Mine works perfectly on v2...
He investiga... foft
07:51 PM Feature #11: Non-uk keyboard support (custom keyboard mapping): its keyboard mapping from ATARI800WIN Emulator, see attached file ndary
07:41 PM Feature #11: Non-uk keyboard support (custom keyboard mapping): What is an a8k file? Is there already a keyboard mapping file format we can use? foft
07:36 PM Feature #14: Svideo core for first prototype: Worth a read for some background: http://codeandlife.com/2012/10/09/composite-video-decoding-theory-and-practice/#mor... foft
07:12 PM Feature #51 (New): Debug port: I'm finding it hard to track down issues in some games/programs. Output debug information so I can look into the prob... foft

06/17/2017

08:17 AM Feature #11: Non-uk keyboard support (custom keyboard mapping): i think reading a key-map file from the SD CART is a good idea, an a8k file? if the key-map file is corrupt or missin... ndary
05:08 AM Feature #11: Non-uk keyboard support (custom keyboard mapping): foft wrote:
> Computer generated c code for TK2 is here: http://atariage.com/forums/topic/263044-developerstesting-r... 917k

06/15/2017

10:24 PM Bug #33: Wizard of Wor: Turbo freezer does not freeze it when its in 'frozen blocks' state but does otherwise. foft
10:21 PM Bug #33: Wizard of Wor: Tried a different version and I get the 'freeze with blocks' at the end of every level. Will have to see what happens... foft
09:30 PM Bug #33: Wizard of Wor: Well I tried many settings in Altirra and can't reproduce with a different hardware variant.
Things I found:
i) Rec... foft

06/14/2017

08:54 PM Bug #33: Wizard of Wor: I see this too. Any luck tracking down the cause? I'm hoping @xxl or @xuel can help me here with their machine code w... foft
07:54 AM Bug #33: Wizard of Wor: I checked a car version on core 14, it started this behavior on the first level after killing monsters and an additio... 917k

06/13/2017

10:20 PM Feature #11: Non-uk keyboard support (custom keyboard mapping): Computer generated c code for TK2 is here: http://atariage.com/forums/topic/263044-developerstesting-required-for-min... foft
08:24 PM Bug #50: CORE13 - Option on initial powerup does not disable BASIC: foft wrote:
> I suggest multiple os roms with a key to toggle
Yeeha! Sound perfect option in my ears!
sadosp
06:45 PM Bug #50: CORE13 - Option on initial powerup does not disable BASIC: Yeah we should absolutely save this setting too foft
06:44 PM Bug #50: CORE13 - Option on initial powerup does not disable BASIC: I suggest multiple os roms with a key to toggle foft
12:24 PM Bug #50: CORE13 - Option on initial powerup does not disable BASIC: I have catch my self many times to set the older Atari OS (memopad) as default on settings menu only for this reason!... sadosp
12:17 PM Bug #50: CORE13 - Option on initial powerup does not disable BASIC: Is the same thing like someone put a simple switch to rom, to disable the Basic on original hardware.
Really I dont ... sadosp
12:12 PM Bug #50: CORE13 - Option on initial powerup does not disable BASIC: foft wrote:
> Basic on/off is an os thing, I don't want to patch the os in firmware.
>
> Yes we need to see how t... sadosp
08:49 AM Bug #50: CORE13 - Option on initial powerup does not disable BASIC: Basic on/off is an os thing, I don't want to patch the os in firmware.
Yes we need to see how to get usb keyboard ... foft
06:12 AM Bug #50: CORE13 - Option on initial powerup does not disable BASIC: I don't remember if in the past have ask from Mark to add a future within settings menu, as to be possible to disable... sadosp
06:03 AM Bug #50: CORE13 - Option on initial powerup does not disable BASIC: Stephen wrote:
> When initially turning on the Eclaire, holding F8 does not disable internal BASIC. However, once b... sadosp
02:18 AM Bug #50 (New): CORE13 - Option on initial powerup does not disable BASIC: When initially turning on the Eclaire, holding F8 does not disable internal BASIC. However, once booted, if I hold F... Stephen
05:31 PM Bug #48: CORE13 - Veronica BASIC not working: foft wrote:
> So all tests work but veronica basic does not?
>
> I know a bit about veronica, I built a veronica ... Stephen
08:51 AM Bug #48: CORE13 - Veronica BASIC not working: So all tests work but veronica basic does not?
I know a bit about veronica, I built a veronica clone for the ultim... foft
02:40 AM Bug #48: CORE13 - Veronica BASIC not working: OK - I got the rotator demo working. However, I cannot get Veronica BASIC to load. It either hangs or says it canno... Stephen
02:25 AM Bug #48: CORE13 - Veronica BASIC not working: Guys - I am very sorry. I was not loading the BIOS first. Veronica is working properly. I tried to delete this, bu... Stephen
02:23 AM Bug #48: CORE13 - Veronica BASIC not working: VREGREAD passes both tests, VRAMTEST passes the 4 tests. Stephen
02:21 AM Bug #48: CORE13 - Veronica BASIC not working: Also, VREGREAD fails both tests, and VRAMTEST fails all 4 tests.
Stephen
02:14 AM Bug #48 (Closed): CORE13 - Veronica BASIC not working: I've tried various RAM and NTSC/PAL settings. When I run "detector.com" from the attached ATR, the screen flickers a... Stephen
11:16 AM Bug #49: CORE13 - NTSC/PAL switching: Yeah I've noticed this too. I think there is a lockup on exiting the menu in general. foft
02:17 AM Bug #49 (Closed): CORE13 - NTSC/PAL switching: I've noticed several times when I switch between PAL and NTSC, then do a "save and apply", when I exit, and exit the ... Stephen

06/12/2017

09:57 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: foft wrote:
> It should work with any decent USB supply. So I think we need to improve our end to handle this variat... sadosp
09:37 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: These are all 'quality' usb supplies - well Apple anyway! foft
09:34 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: It should work with any decent USB supply. So I think we need to improve our end to handle this variation.
I check... foft
09:23 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: foft wrote:
> I have power supplies who state 5V, but if I measure them they are not.
I know Mark, and this is t... sadosp
09:09 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: ndary wrote:
> i have a meter, just need clear instruction what to do and where to check
>
> Nir
Prepare your ... sadosp
09:03 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: I have power supplies who state 5V, but if I measure them they are not.
You can measure on the joystick ports - o... foft
08:58 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: i have a meter, just need clear instruction what to do and where to check
Nir ndary
08:50 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: Same reading in the 1st board also?
What the other guys said about it? None have a multi meter to check the voltag... sadosp
08:38 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: I mean tps63002.
I have a multimeter. It still reads 3.8V today after the regulator - and 5V on the input. I trust... foft
08:36 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: I read it at the switch. I checked with 4 psus - checking each time on the regulated outputs that my scope was still ... foft
08:34 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: Mark, I think is time to send you a digital multi-meter as a gift! ;-)
I have a question. You read the 5v directly... sadosp
08:21 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: "It is specified that devices' configuration and low-power functions must operate down to 4.40 V at the hub port by U... foft
08:17 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: "The ATX power supply specification states the 5VUSB rail can be between +4.75V and +5.25V."
I guess we need a reg... foft
07:59 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: OK, I restarted my scope software and now get the correct readings. So a bit of a mystery but I suspect a plain old b... foft
12:36 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: Hi Mark.
I use my 4 digits digital multimeter to take readings. My analogue scope TEK2445, isn't usefull at all for ... sadosp
07:29 AM Bug #47: CORE 13 - Paddle, Touchtablet issues: Ok, so assuming my scope is wrong for now. Its a usb one, I don't trust the absolute levels that much. What are you u... foft

06/11/2017

10:41 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: Even a worthless psu rated at 5v @ 500mA who in reality supply with 5.26v, after the regulator read 3.333v sadosp
10:33 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: I use these two power adapters below..
[[https://m-service.prom.ua/p47863721-zaryadnoe-ustrojstvo-white.html]]
... sadosp
10:14 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: foft wrote:
> Maybe my tools are just not calibrated properly.
I don't have touch tablet in my possession, but I ... sadosp
10:14 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: foft wrote:
> Maybe my tools are just not calibrated properly.
I don't have touch tablet in my possession, but I ... sadosp
10:12 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: foft wrote:
> Maybe my tools are just not calibrated properly.
I don't have touch tablet in my possession, but I ... sadosp
10:11 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: foft wrote:
> Maybe my tools are just not calibrated properly.
I don't have touch tablet in my possession, but I ... sadosp
09:04 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: Maybe my tools are just not calibrated properly. Well anyway the touch tablet does not seem to work with a decent PSU... foft
08:59 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: foft wrote:
> Still this this should be checked, but think its a red herring. I get the same reading on my scope - a... sadosp
08:52 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: OK, I found that if I connect the Eclaire to my laptop for power, it works. If I connect it to a PSU, it doesn't! The... foft
08:32 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: Still this this should be checked, but think its a red herring. I get the same reading on my scope - and on the v1 an... foft
08:19 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: Going to check this on my scope, I don't trust my multimeter... foft
07:53 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: The odd thing is I get 3.8V instead of 3.3V. I don't understand that at all, investigating... This would push the thr... foft
07:42 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: foft wrote:
> I checked the touch tablet, confirmed not working on the new board. Very odd since this worked on v1 a... sadosp
07:39 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: I checked the touch tablet, confirmed not working on the new board. Very odd since this worked on v1 and paddles are ... foft
07:36 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: ", then I will check the touch tablet" foft
07:36 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: Yeah I mixed them up.
We swapped joystick ports 0/1 and 2/3 on the silkscreen. I made the same changes in the core... foft
07:30 PM Bug #47: CORE 13 - Paddle, Touchtablet issues: To one point I don't remember till which firmware version, these work well. Maybe Mark later confuse something in Cor... sadosp
05:47 PM Bug #47 (Closed): CORE 13 - Paddle, Touchtablet issues: Touch Tablet not working
Paddles buttons and Knobs are not correlate for the same Paddle
ndary
09:13 PM Bug #45: CORE10 - IDE2+ SDX not working: testing IDE2+ on an ULTIMATE 1MB does not behave correctly as well ndary
09:08 PM Bug #45: CORE10 - IDE2+ SDX not working: Does the IDE2+ work in those modes on a real system? I mean on a standard version of those upgrades, not one of these... foft
08:53 PM Bug #45: CORE10 - IDE2+ SDX not working: Stephen wrote:
> In CORE10, when I boot with the IDE2+ installed, the machine initially goes right into self test mo... Stephen
05:44 PM Bug #45: CORE10 - IDE2+ SDX not working: Tested and working on core 13
Nir ndary
08:48 PM Bug #25: F10 Hard Reset Ignore inserted cartridge (Core v7): This is still on the list, but not yet in place... foft
05:45 PM Bug #43: Core 10 - IDE2+ Menu does not show when powering the computer with START key pressed: Tested and working on Core 13, need other guys to test on MIO and BlackBox
Nir ndary
12:11 PM Bug #43: Core 10 - IDE2+ Menu does not show when powering the computer with START key pressed: More info from Simus:
$D800..$DDFF is a ROM, $DE00...$DFFF is a RAM.
MPD is kept low all the time when apropriated ... foft
03:09 PM Bug #34 (Closed): Problem booting with Core 9: this happen on every core after flashing, to solve it i simply remove and put back the SD Card and it works ndary
03:07 PM Bug #44 (Closed): CORE 11 - Bug in PBI - EclaireXL will not boot with IDE2+ Is connected and when Turbo Freezer connected goes directly to Cart EMU not main screen: Checked IDE2+ On core 13 and i works!
case closed ndary
02:09 PM Bug #44: CORE 11 - Bug in PBI - EclaireXL will not boot with IDE2+ Is connected and when Turbo Freezer connected goes directly to Cart EMU not main screen: Even on v13 it goes straight to the cart emu menu. My turbo freezer goes straight to the cart emu menu on my 600xl th... foft
01:54 PM Bug #44: CORE 11 - Bug in PBI - EclaireXL will not boot with IDE2+ Is connected and when Turbo Freezer connected goes directly to Cart EMU not main screen: Found a bug I introduced here. When MPD_N is low I was also disabling the rest of the OS rom... Ooops! IDE2+ holds it... foft
03:07 PM Bug #46 (Closed): CORE 10 - VOICE BOX does not work with Eclaire board: solved in CORE 13 ndary
01:53 PM Bug #46: CORE 10 - VOICE BOX does not work with Eclaire board: I've wired this up in core 13, but I need to checking the timing is correct on the logic analyzer. foft
11:30 AM Bug #46: CORE 10 - VOICE BOX does not work with Eclaire board: Pin 12 of SIO connector is used only by ancient Atari's 400 and 800 as a 12v dc supply. On eclaire XL is unconnected.... sadosp
10:01 AM Bug #46: CORE 10 - VOICE BOX does not work with Eclaire board: I guess you mean pin11? I think you confirmedthis works, but is quiet?
The problem is I think that this uses sio c... foft

06/10/2017

11:43 PM Document: Main Board Interface 1 & 2 Pin-outs - v3 prototype: sadosp
11:41 PM Interface Pinouts V3.0.png: sadosp
01:45 PM Bug #46 (Closed): CORE 10 - VOICE BOX does not work with Eclaire board: i tested my Voice Box on a real Atari and on the Eclaire board and on the Eclair it does not work!
to run the Voic... ndary

06/09/2017

11:40 PM Bug #43: Core 10 - IDE2+ Menu does not show when powering the computer with START key pressed: ndary wrote:
> can you confirm that you get to the MIO Menu?
>
> Nir
After dinner I will find a power supply f... Stephen
09:45 PM Bug #43: Core 10 - IDE2+ Menu does not show when powering the computer with START key pressed: can you confirm that you get to the MIO Menu?
Nir ndary
09:38 PM Bug #43: Core 10 - IDE2+ Menu does not show when powering the computer with START key pressed: ndary wrote:
> i found this document.. can it be missing voltage on the PBI port?
>
> the interface seems to work... Stephen
08:23 PM Bug #43: Core 10 - IDE2+ Menu does not show when powering the computer with START key pressed: IDEPlus info from Simius:
IDE+ detaches OS ROM between $D800 and $DFFF and plug his own memory there. I uses also $D... foft
09:59 PM Bug #44: CORE 11 - Bug in PBI - EclaireXL will not boot with IDE2+ Is connected and when Turbo Freezer connected goes directly to Cart EMU not main screen: Though that logic should only get hit after it stabilises... Hmmm. Well registering it anyway (grasping at straws!!) foft
09:46 PM Bug #44: CORE 11 - Bug in PBI - EclaireXL will not boot with IDE2+ Is connected and when Turbo Freezer connected goes directly to Cart EMU not main screen: I think I know why it won't boot with v11.
MPD_N is combinatorial logic driven from the address - and I use it too... foft
09:26 PM Bug #44: CORE 11 - Bug in PBI - EclaireXL will not boot with IDE2+ Is connected and when Turbo Freezer connected goes directly to Cart EMU not main screen: I am also confirming that with Core 11, the exlaire will not boot with IDE2+ Rev C. A video signal is generated as m... Stephen
07:10 AM Bug #44: CORE 11 - Bug in PBI - EclaireXL will not boot with IDE2+ Is connected and when Turbo Freezer connected goes directly to Cart EMU not main screen: I see the cart emu thing, I had not tested that... I had it disabled. Interesting, will check the manual for when tha... foft
09:59 PM Feature #2: PBI support: Turn on data write to bus earlier, for things that snap it early (like IDE2+).
Register MPD_N before feeding to the... foft
09:29 PM Bug #45 (Closed): CORE10 - IDE2+ SDX not working: In CORE10, when I boot with the IDE2+ installed, the machine initially goes right into self test mode. Pressing rese... Stephen

06/08/2017

11:22 PM Bug #44 (Closed): CORE 11 - Bug in PBI - EclaireXL will not boot with IDE2+ Is connected and when Turbo Freezer connected goes directly to Cart EMU not main screen: Just tested CORE 11 and there is Bug in PBI - EclaireXL will not boot with IDE2+ Is connected and when Turbo Freezer ... ndary
09:43 PM Bug #42: Core 8 - Mic level is low: I think on the final board we should add a passive low pass filter to the ADC inputs. Also are large resistor to pull... foft
10:18 AM Bug #42: Core 8 - Mic level is low: yes Panos, the noise is when SIO of the XC12 is connected ndary
09:39 PM Bug #43: Core 10 - IDE2+ Menu does not show when powering the computer with START key pressed: SO in v10 RST_N was just floating... foft
09:38 PM Bug #43: Core 10 - IDE2+ Menu does not show when powering the computer with START key pressed: Found an issue with RST_N. I had disconnected it in v10 (I forgot) because when I reset the freezer broke. Well I was... foft
09:01 PM Bug #43: Core 10 - IDE2+ Menu does not show when powering the computer with START key pressed: I checked MPD...
If MPD and EXTSEL are used in conjunction that seems to work fine.
If just MPD is used to expo... foft
08:34 PM Bug #43: Core 10 - IDE2+ Menu does not show when powering the computer with START key pressed: There is 5V on pin 47 and pin 48.
I see it drives EXSEL and MPD. I thought I'm handling that case properly, but I... foft
08:09 PM Bug #43: Core 10 - IDE2+ Menu does not show when powering the computer with START key pressed: no it does not, i already tried it Panos
Nir ndary
07:31 PM Bug #43: Core 10 - IDE2+ Menu does not show when powering the computer with START key pressed: Nir,
If you power on eclaireXL and go to Basic, after keep down the start key and simultaneously press and leave t... sadosp
07:21 PM Bug #43: Core 10 - IDE2+ Menu does not show when powering the computer with START key pressed: i found this document.. can it be missing voltage on the PBI port?
the interface seems to work on the Eclair, when... ndary
06:45 PM Bug #43: Core 10 - IDE2+ Menu does not show when powering the computer with START key pressed: no, i dont have a logic analyzer or the schematics...
let me see what info i can gather ndary
06:34 PM Bug #43: Core 10 - IDE2+ Menu does not show when powering the computer with START key pressed: Perhaps we can test it by poking/peeking regs from basic... foft
05:36 PM Bug #43: Core 10 - IDE2+ Menu does not show when powering the computer with START key pressed: Does the rest of it work, just not the menu?
Do you have a logic analyzer? I can outputs some signals on the gpio ... foft
04:39 PM Bug #43 (Closed): Core 10 - IDE2+ Menu does not show when powering the computer with START key pressed: the PBI device i am testing is the IDE2+ external interface that plugs to the PBI port
when i reset the computer wit... ndary
04:37 PM Convert SOF file to JIC and Flashing EclaireXL V2 PCB core.pdf: ndary

06/07/2017

10:46 PM Bug #41: Core 8 - the backgound music in Gene & LMS demos are not the same as on a real ATARI: Just trying gene.xex - any particular point that you hear the difference? I'll have to check my real Atari later - ni... foft
01:07 PM Bug #41: Core 8 - the backgound music in Gene & LMS demos are not the same as on a real ATARI: Interesting. Did the Atari you tested on have dual pokey?
v9 only changes pbi support, no pokey work. foft
11:31 AM Bug #41: Core 8 - the backgound music in Gene & LMS demos are not the same as on a real ATARI: confirmed this bug also in CORE9 ndary
10:34 PM PBI support!: Core v10 is out for both v1 and v2/3
The turbo freezer works! Both of them! foft
10:27 PM Feature #2: PBI support: Please now test some other devices - and let me know how you get on:-) I can't guarantee its safe but the fact the fr... foft
10:12 PM Feature #2: PBI support: Woohoo, freezer is working after reset - and ramdisk is working from freezer! foft
10:08 PM Bug #39 (Closed): Internal turbo freezer crashes on v9: foft
10:07 PM Bug #39: Internal turbo freezer crashes on v9: Fixed in v10 (being built)
Issue was down to interaction between pbi takeover when freezer has disabled atari. e.g... foft
05:33 PM Bug #16 (Closed): Audio bug report for Altirra: Many thanks Nir foft
02:13 PM Bug #16: Audio bug report for Altirra: I Confirm that these Audio tests sound the same on a real Atari and on EclairXL board
Nir ndary

06/06/2017

09:19 PM Feature #2: PBI support: I added output of internal reads to the bus. I also fixed some cases around writes.
Now the external turbo freezer... foft
09:16 PM Bug #42: Core 8 - Mic level is low: Noise is there only when the SIO connector of XC12 is connected?
sadosp
09:15 PM Bug #42: Core 8 - Mic level is low: Yeah we need a digital filter for that, part of the reason I don't want to make it louder yet:-). I found it pretty l... foft
09:00 PM Bug #42: Core 8 - Mic level is low: yes i connected correctly... and the volume still low..
i also notices that when the X12 is connected but nothing ... ndary
08:26 PM Bug #42: Core 8 - Mic level is low: I don't have any tapes! I've not tuned the volume but it seemed pretty loud to me... foft
08:07 PM Bug #42: Core 8 - Mic level is low: Have you connect these with right polarity? I mean ground to ground etc?
sadosp
07:40 PM Bug #42 (New): Core 8 - Mic level is low: I connect the 2 pin header of MIC3 from the top board to the Bottom board (next to the speaker output)
and placed on... ndary
07:16 PM Bug #41 (New): Core 8 - the backgound music in Gene & LMS demos are not the same as on a real ATARI: i Am attaching two demos that are set to run on an PAL Atari with 576k or 1meg ram
in both the background music is n... ndary
08:57 AM Feature #28 (Closed): XEX boot loader replacement: foft
08:00 AM Feature #28: XEX boot loader replacement: foft wrote:
> Replace XEX boot loader with a better one
Das Omen works fine. You do not need to replace the loa... xxl
08:56 AM Bug #20 (Closed): Bugs in DAS OMEN Demo: foft
06:46 AM Bug #38: Numen crashes on v9: (i managed to flash core 9 successfully, and Numen work when the memory is set to 320k compyshop.
numben crashed whe... ndary

06/05/2017

10:49 PM Bug #39: Internal turbo freezer crashes on v9: (sorry i confirm that turbo freezer does crash on v9, not in the turbo freezer menu, but after you exist TB Freezer t... ndary
10:43 PM Bug #39: Internal turbo freezer crashes on v9: (I managed to flash CORE 9 (.SOF) file and the compute rebooted,
and pressing DEL take me to the Freezer software, ... ndary
08:12 PM Videos: Nir posted a couple of great videos, really great. I particularly enjoyed seeing the side2 streaming working.
http... foft
03:23 PM Bug #34: Problem booting with Core 9: ndary wrote:
> i did with same result, can anyone else confirm that core 9 works on on his v2 board?
>
> Nir
J... Stephen

06/04/2017

02:13 PM Feature #40: Add support for Interlace mode (in scaler): Actually this works in 15KHz mode! Try it in 'RGB' mode on a CRT. Also I found it works in 'scandouble mode' too iirc... foft
01:54 PM Feature #40 (New): Add support for Interlace mode (in scaler): attached is the Memopad 480i tool that simulate interlace mode on the ATARI 800XL,
ExclairXL does not emulate inter... ndary
01:20 PM Bug #34: Problem booting with Core 9: Thanks for checking Nir. I guess it must be on the 'edge' and thus some boards work and not others. Its working well ... foft
12:45 PM Bug #34: Problem booting with Core 9: i did with same result, can anyone else confirm that core 9 works on on his v2 board?
Nir ndary
09:22 AM Bug #34: Problem booting with Core 9: One thing to try, can you see if it's the same with a few different power supplies? foft

06/03/2017

09:58 PM Bug #39 (Closed): Internal turbo freezer crashes on v9: Pressing delete to activate internal turbo freezer crashes the core foft
09:57 PM Bug #38 (Closed): Numen crashes on v9: Look into why foft
09:57 PM Feature #37 (Closed): SD card insertion support: If an SD card is removed/inserted we should detect it and initialize fat. Should be no need to reboot. The detect lin... foft
08:44 PM Bug #5 (Closed): SIDE2 does not work: Great, thanks Roy. Will close this for now, please reopen if it breaks again! foft
08:41 PM Bug #5: SIDE2 does not work: foft wrote:
> In v8, uh oh! I don't think I changed anything before v8 that would fix this... I will have to get Roy... RoyE
12:31 PM Bug #5: SIDE2 does not work: In v8, uh oh! I don't think I changed anything before v8 that would fix this... I will have to get RoyE to double che... foft
09:04 AM Bug #5: SIDE2 does not work: I Confirm that SIDE 2 cart work on core8, should we close this bug?
Nir ndary
12:37 PM Support #29 (Closed): LED for SIO activity: Great, closing. I'll note on the wiki that we should have a header for this on the final board. foft
12:36 PM Bug #20: Bugs in DAS OMEN Demo: So is the one a basic on/off issue? foft
12:33 PM Feature #28: XEX boot loader replacement: Or a patched OS, where the BASIC is turned off by default (you need to press OPTION in order to have BASIC). This is ... jozsef
12:30 PM Feature #28: XEX boot loader replacement: I'm actually tempted to make the 'menu' less emulator like where possible. It is a hardware recreation and having a p... foft
12:29 PM Feature #28: XEX boot loader replacement: Remember we're not an emulator and I'm hesitant to add extra portb logic etc or logic to force hold down keys for cer... foft
12:28 PM Feature #28: XEX boot loader replacement: Do you mean in F11? I never use this one, but I think its ok to hold option if you need it isn't it? The USB keyboard... foft
09:48 AM Feature #28: XEX boot loader replacement: Mark,
i found that the existing XEX loader behave better then i originally reported,
the problem is that when y... ndary
12:29 PM Bug #35: When connecting ST Mouse to any JOY PORT on the expantion port, navigation on the EclairXL Settings menu not possible (Core8): In fact, stick(0) depends on the mouse's position. jozsef
12:26 PM Bug #35: When connecting ST Mouse to any JOY PORT on the expantion port, navigation on the EclairXL Settings menu not possible (Core8): stick(0) = 8, strig(0) = 1 jozsef
12:25 PM Bug #35: When connecting ST Mouse to any JOY PORT on the expantion port, navigation on the EclairXL Settings menu not possible (Core8): I agree I should change the firmware to still allow keyboard movement when the joystick is held on. foft
12:17 PM Bug #35: When connecting ST Mouse to any JOY PORT on the expantion port, navigation on the EclairXL Settings menu not possible (Core8): The joystick buttons and directions must be released to move. I guess the mouse presses some direction when idle. Wha... foft
11:19 AM Bug #35: When connecting ST Mouse to any JOY PORT on the expantion port, navigation on the EclairXL Settings menu not possible (Core8): I have confirm this behavior with Core7 (but strangely not always). More to this: I have SIO2SD attached to Eclaire, ... jozsef
09:31 AM Bug #35 (New): When connecting ST Mouse to any JOY PORT on the expantion port, navigation on the EclairXL Settings menu not possible (Core8): I have connected an ST Mouse o the EclairXL joyport to try and load some software that use the ST mouse but when the ... ndary
12:27 PM Bug #33: Wizard of Wor: Thanks for checking more versions, always worthwhile. We need to work out what is going wrong, or if its just a game ... foft
11:07 AM Bug #33: Wizard of Wor: Tried it today running more versions of WoW with the same results.
Addition to the behavior I described, when the ga... jozsef
12:23 PM Bug #36: Joystick is always emulated through the USB keyboard arrow keys: The keyboard is mapped to match the Atari _layout_. Sorry the arrow keys are in the same location as on the 800XL. i.... foft
10:48 AM Bug #36: Joystick is always emulated through the USB keyboard arrow keys: Its is not about the keyboard mapping...
if you connect just a USB keyboard (not one with built in mouse) and you ... ndary
10:31 AM Bug #36 (Rejected): Joystick is always emulated through the USB keyboard arrow keys: Not a bug, the keyboard matches the Atari layout.
See the core manual.
There is a feature request for custom mapp... foft
09:34 AM Bug #36 (Rejected): Joystick is always emulated through the USB keyboard arrow keys: I have connected only a USB keyboard (not mouse, or USB keyboard with built in mouse), and noticed when i try to ru... ndary
12:23 PM Feature #21 (Closed): Mirax Force game crash: Closing, not a bug with the loader. Just need to hold option to disable basic as usual! foft
12:20 PM Feature #21: Mirax Force game crash: Its the same as the 800xl, portb disables basic and the os changes portb when holding option. Of course you can chang... foft
10:54 AM Feature #21: Mirax Force game crash: notice that if you hold the OPTION KEY (F8) before selecting the file, it load correctly,
thus i believe we need to ... ndary
08:20 AM Bug #34: Problem booting with Core 9: Though thinking some more if you get 'no sync' then that is before all the new logic starts, so more likely the build... foft
07:31 AM Bug #34: Problem booting with Core 9: Its either board-board instability due to small timing differences or the new input pins I guess.
Can you check th... foft
12:49 AM Bug #34 (Closed): Problem booting with Core 9: upgraded successfully to core 9
but when powering on the board, the ExclairXL boot one out of six times..
when i... ndary
07:33 AM Bug #31: HDMI Audio generate high pitch noise (Core 8): HDMI audio to me seems very broken... Even just the 'bubbling' boot sound comes out wrong in my opinion. foft
07:32 AM Bug #31: HDMI Audio generate high pitch noise (Core 8): So you are saying it happens with v7? OK that rules out the adc then. foft
12:29 AM Bug #31: HDMI Audio generate high pitch noise (Core 8): it happens with CORE 8 & 9 as well ndary

06/02/2017

10:56 PM Bug #4 (Closed): Galaxian flickers on scrolling - when using real cartridge: Fixed in v9 foft
10:50 PM Feature #2: PBI support: First cut released as v9. Sure there are some bugs, try at your own risk! foft
10:25 PM Feature #2: PBI support: I took a look at the turbo freezer on signaltap, I can't see it even trying to pull refresh after a reset. So I guess... foft
10:10 PM Feature #2: PBI support: Synced gtia delays to end of original 6502 cycle time and now acid is passing again. foft
03:45 PM Feature #2: PBI support: Well that horrible dma clock patch led to a complete acid pass except for a gtia failure. I see in gtia I have colour... foft
03:38 PM Feature #2: PBI support: I've been squashing test failures related to moving the cpu clock later in the '6502 cycle' due to PBI. None of these... foft
10:49 PM Bug #25: F10 Hard Reset Ignore inserted cartridge (Core v7): Bumped to v10... foft
10:10 PM Bug #25: F10 Hard Reset Ignore inserted cartridge (Core v7): Arg, of course I turned off pbi/cart in turbo mode and on zpu accesses... Better change that too I guess otherwise I ... foft
09:42 PM Bug #25: F10 Hard Reset Ignore inserted cartridge (Core v7): Added to svn code foft
10:49 PM Bug #27 (Closed): USB D-PAD Joystick support on CORE7: Decided to call pbiv28 v9... Closing as complete. foft
10:23 PM Bug #27: USB D-PAD Joystick support on CORE7: Confirmed good as of pbiv28.sof. This release is almost ready for v9.sof, but some issues to fix first... foft
09:29 PM Bug #27: USB D-PAD Joystick support on CORE7: Switched this to another output so it should no longer crash in next release foft
10:28 AM Bug #27: USB D-PAD Joystick support on CORE7: I checked the code and I'm using zpu_out5 for both joystick and video mode! foft
10:31 PM Feature #11: Non-uk keyboard support (custom keyboard mapping): The mapping from ps2 to atari key code is here:
http://www.64kib.com/atarixlfpga_svn/trunk/atari_800xl/common/a8core... admin
08:07 PM Bug #33: Wizard of Wor: If this is confirmed it will need some digging to get to the root cause. Anyone up for the challenge? foft
04:29 PM Bug #33 (Closed): Wizard of Wor: Loading it from an external sio2SD drive with core 7:
At least on the 4th of 5th level, the monsters start appearing... jozsef
05:06 PM Support #29: LED for SIO activity: Connected to SIO-IN and 5V (SIO-IN is reversed). Works fine. Thank you. jozsef
09:54 AM Feature #32: option to connect the original ATARI XL keyboard to ExclairXL: I mean I have the pokey signals and can break them out. To use an XL one we'd need a board with a suitable socket and... foft
08:39 AM Feature #32: option to connect the original ATARI XL keyboard to ExclairXL: yes i did.. but i was hoping for a real XL keyboard.. not the mushy XE ones :) ndary
07:11 AM Feature #32: option to connect the original ATARI XL keyboard to ExclairXL: You've also seen I had an XEGS keyboard connector on the old board?
http://www.64kib.com/eclairexl.html
We have s... foft
07:12 AM Bug #31: HDMI Audio generate high pitch noise (Core 8): Did it on core 7 btw? If so I guess its aliasing from the adc noise? I need a low pass filter on input to the HDMI co... foft
07:08 AM Bug #31: HDMI Audio generate high pitch noise (Core 8): The HDMI audio has some issues, I have another bug to find this. foft
01:33 AM Bug #18: Power on Switch: ndary wrote:
> in a REAL ATARI XL/XE computer you switch the computer on by flipping the POWER SWITCH UP, but in the... Stephen

06/01/2017

11:16 PM Feature #32 (New): option to connect the original ATARI XL keyboard to ExclairXL: IT would be great to be able and connect the Original ATARI XL keyboard to EclairXL board,
such option has been... ndary
11:08 PM Bug #31 (Closed): HDMI Audio generate high pitch noise (Core 8): The Audio of the HDMI port generate high pitch sound..
you can hear it when TAPE LOADS, or though disk driver SIO ... ndary
11:06 PM Bug #30 (Feedback): TAPE does not play AUDIO on the Right Chanel (Eucational tapes cannot be heard): will make a cable and continued testing ndary
10:50 PM Bug #30: TAPE does not play AUDIO on the Right Chanel (Eucational tapes cannot be heard): or i will build a cable are test, thanks
Nir ndary
10:36 PM Bug #30: TAPE does not play AUDIO on the Right Chanel (Eucational tapes cannot be heard): @Nir
As for the XC12 tape corder, just now I see that it haven't a PSU, so must take their power supply entirely fro... sadosp
10:23 PM Bug #30: TAPE does not play AUDIO on the Right Chanel (Eucational tapes cannot be heard): This is only in v8 too foft
10:16 PM Bug #30: TAPE does not play AUDIO on the Right Chanel (Eucational tapes cannot be heard): Have you seen the two pole pin header on right side of the sub board? Is for this exact reason.
You must make first ... sadosp
10:03 PM Bug #30 (Closed): TAPE does not play AUDIO on the Right Chanel (Eucational tapes cannot be heard): tried to put an AUDIO Tape
POKE 54018,52 [RETURN] should stream AUDIO that is recorded on the right channel and it... ndary
08:20 PM Support #29: LED for SIO activity: Interface 2 pin 36 (SIO out) and interface 2 pin 31 (GND). With a suitable resistor of course since this is 5V. foft
05:04 PM Support #29 (Closed): LED for SIO activity: Where can I connect a LED to indicate SIO activity (soldering is not a problem, if required)?
POWER and RESET are ... jozsef
07:21 PM Bug #17: NTSC crashing on some builds: ndary wrote:
> changed the Core to v8 and when chancing the video mode to NTSC the screen crashes
>
> Nir
I re... sadosp
07:13 PM Bug #17: NTSC crashing on some builds: changed the Core to v8 and when chancing the video mode to NTSC the screen crashes
Nir ndary
06:40 AM Bug #25: F10 Hard Reset Ignore inserted cartridge (Core v7): OK, I'll add that in v9 foft

Also available in: Atom

Project

General

Profile

EclaireXL

Activity

Activity

06/30/2017

06/29/2017

06/27/2017

06/23/2017

06/22/2017

06/21/2017

06/20/2017

06/17/2017

06/15/2017

06/14/2017

06/13/2017

06/12/2017

06/11/2017

06/10/2017

06/09/2017

06/08/2017

06/07/2017

06/06/2017

06/05/2017

06/04/2017

06/03/2017

06/02/2017

06/01/2017